? coilcraft, inc. 2010 specifications subject to change without notice. please check our website for latest information. chip inductors C 0402af series (1005) document 422-1 document 422-1 revised 10/20/08 inductance 2 srf typ 3 dcr max 4 i rms 5 part number 1 5% (nh) (mhz) (ohms) (ma) 0402af-200xjl_ 20 2600 0.050 1600 0402af-220xjl_ 22 2500 0.065 1300 0402af-330xjl_ 33 2300 0.060 1400 0402af-360xjl_ 36 2300 0.075 1300 0402af-390xjl_ 39 2200 0.115 830 0402af-510xjl_ 51 1930 0.070 1100 0402af-560xjl_ 56 1900 0.095 1000 0402af-720xjl_ 72 1650 0.100 1000 0402af-780xjl_ 78 1600 0.130 970 0402af-101xjl_ 100 1400 0.160 900 0402af-141xjl_ 140 1220 0.260 630 0402af-181xjl_ 180 1150 0.280 560 0402af-201xjl_ 200 1000 0.440 400 0402af-221xjl_ 220 1150 0.530 380 0402af-251xjl_ 250 900 0.360 520 0402af-271xjl_ 270 860 0.550 360 0402af-301xjl_ 300 860 0.410 420 0402af-331xjl_ 330 820 0.560 350 0402af-361xjl_ 360 810 0.575 360 0402af-391xjl_ 390 760 0.750 300 0402af-421xjl_ 420 700 0.700 340 0402af-471xjl_ 470 650 0.730 310 0402af-561xjl_ 560 600 0.920 200 1. when ordering, please specify termination and packaging codes: 0402af-561xj lw termination: l = rohs compliant gold over nickel over silver- palladium-glass frit. special order: t = rohs tin-silver-copper (95.5/4/0.5) or s = non-rohs tin-lead (63/37). packaging: w =7 machine-ready reel. eia-481 punched paper tape (2000 parts per full reel). u = less than full reel. in tape, but not machine ready. to have a leader and trailer added ($25 charge), use code letter w instead. 2. inductance measured at 7.9 mhz using a coilcraft smd-f test fixture and coilcraft-provided correlation pieces with an agilent/hp 4286 impedance analyzer. 3. srf measured using agilent/hp 8753d network analyzer and coilcraft smd-d test fixture. 4. dcr measured on cambridge technology micro-ohmmeter and a coilcraft ccf858 test fixture. 5. current that causes a 15c temperature rise from 25c ambient. because of their open construction, these parts will not saturate. refer to doc 362 ?soldering surface mount components? before soldering. ? higher inductance values than other 0402 inductors ? ferrite construction for high current handling ? 23 inductance values from 20 nh to 560 nh a b overall e f f d terminal e h c g terminal wraparound: approx 0.007/0,18 both ends pick and place material recommended land pattern a max b max c max d e f g h 0.044 0.026 0.026 0.020 0.009 0.017 0.018 0.026 inches 1,12 0,66 0,66 0,51 0,23 0,43 0,46 0,66 mm designer?s kit c397 contains 20 each of all values core material ferrite terminations rohs compliant gold over nickel over silver-palladium- glass frit. other terminations available at additional cost. weight 0.9 ? 1.1 mg ambient temperature ?40c to +85c with i rms current, +85c to +100c with derated current storage temperature component: ?40c to +100c. packaging: ?40c to +80c resistance to soldering heat max three 40 second reflows at +260c, parts cooled to room temperature between cycles temperature coefficient of inductance (tcl) +25 to +150 ppm/c moisture sensitivity level (msl) 1 (unlimited floor life at <30c / 85% relative humidity) failures in time (fit) / mean time between failures (mtbf) one per billion hours / one billion hours, calculated per telcordia sr-332 packaging 2000 per 7 reel. paper tape: 8 mm wide, 0.68 mm thick, 2 mm pocket spacing pcb washing only pure water or alcohol recommended
? coilcraft, inc. 2010 chip inductors C 0402af series specifications subject to change without notice. please check our website for latest information. document 422-2 revised 10/20/08 document 422-2 1 10 1000 100 0.001 0.01 110 0.1 inductance (nh) frequency (ghz) 20 nh 56 nh 100 nh 270 nh 560 nh typical l vs frequency 16 14 12 10 8 6 4 2 0 1 10 100 q factor frequency (mhz) 270 nh 560 nh 20 nh 56 nh 100 nh typical q vs frequency -40 -20 0 20 40 60 80 100 120 ambient temperature (c) 120 110 100 90 80 70 60 50 40 30 20 10 0 percent of rated rms i 25c irms derating
|
